VIDEO

Similarly, it is asked, what size pipe wrench do I need?

An 18-inch straight pipe wrench is also commonly used in the industry for up to 2 1/2-inch-diameter pipe. It is another good initial purchase. Regardless of the type of wrench purchased, contractors need to make sure they are selecting a quality wrench.

One may also ask, what is a pipe wrench called? Pipe wrench. Another type of wrench often used on pipes, the plumber wrench, is also called a pipe wrench in some places. The Stillson wrench is an adjustable wrench (spanner) with hardened serrated teeth on its jaws.

Additionally, how does pipe wrench work?

An end pipe wrench has a head at a bit of angle and is designed to be used on pipes close to the wall or parallel work. An offset pipe wrench is used to grab onto pipes at awkward angles or in tight spots. A compound leverage pipe wrench is used for seized joints and provides extra leverage.

Is a monkey wrench a pipe wrench?

The term monkey wrench is also sometimes used loosely, usually by non-tradespeople, to refer to the pipe wrench (owing to their broadly similar shapes), but tradespeople (plumbers, pipefitters) usually speak more precisely than that. A wrench with smooth jaws (no teeth) is not used for turning threaded pipe.

How heavy is a pipe wrench?

The aluminum pipe wrench weighs much less than the cast-iron models, at just 11 pounds it's much more comfortable to transport with other tools, so you can take it anywhere you need to go.

How do you maintain a pipe wrench?

Face a pipe wrench forward. Turn wrench so pressure is against heel jaw. Pull, rather than push on the pipe wrench handle. Maintain a proper stance with feet firmly placed to hold your balance.

Do I need two pipe wrenches?

A pipe wrench can also be essential when removing large drain clean-out fittings, such as the main sewer clean-out. In some instances, it's helpful to have two pipe wrenches to prevent stress on the fitting—one wrench holds the pipe or fitting steady, and another wrench to turn the adjoining piece.

How much does a 36 inch pipe wrench weight?

Weight: 19 lbs.

How much is a basin wrench?

Because it is designed only for use on faucet mounting nuts, a basin wrench's uses are limited. But from time to time every homeowner faces faucet replacement, and when you need one, a basin wrench will prove to be the best $10 or $20 you ever spent.

What size nut uses a 1/2 wrench?

US Bolt Head/Wrench SizeBolt Diameter Head and Wrench Size Hex Bolt - Lag Bolt - Square Bolt Heavy Hex Bolt 5/16" 1/2" - 3/8" 9/16" - 7/16" 5/8" -

Is 10mm bigger than 3 8?

It's the same size. 3/8 is in inch and and its 10mm.

How many wrench sizes are there?

There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters). In-between sizes are available too, starting with 1/4 inch (0.6 centimeters) and increasing every sixteenth of an inch (0.16 centimeters).

What is the next size up from 1/2 inch?

Ear Gauge to MM Conversion TableGauge Millimeters(mm) Inches 00g 10 mm 3/8" 11 mm 7/16" 12 mm 1/2" 14 mm 9/16"

What are the most common metric wrench sizes?

Re: Most common metric bolt sizes Used to be (back in the 70's and 80's) that European manufacturers used the 13mm and 10mm fasteners the most; followed by the 14, 17, and 19mm. The Asian manufacturers used the 12mm and 10mm as the most common, followed by the 15, 17 and 19mm.

What's the next size up from 13 16?

Wrench Size Chart for BoltsBolt Diameter Wrench Size (Standard) Wrench Size (Metric) 9/16" 13/16" 21mm 5/8" 15/16" 24mm 3/4" 1-1/8" 29mm 7/8" 1-5/16" 34mm

How are nut sizes measured?

Place the end of a measuring tape on one of the flat sides of the nut's outer perimeter. Stretch the tape measure across the nut's diameter to the flat-side directly across from the one your pulling from. If the nut is metric, count the number of lines on the tape measure to find the measurement.

What socket is smaller than 9 32?

SAE to Metric Conversion ChartSAE Size Metric Size Inches Decimal 9/32" 0.281 5/16" 0.313 8mm 0.315 11/32" 0.344

What size bolt has a 14mm head?

Metric Bolt Head/Wrench SizeBolt Diameter (mm) Head/Wrench Size (mm) ANSI/ISO JIS 8 13 12 10 16 14 12 18 17

What does a monkey wrench look like?

A monkey wrench is an adjustable wrench with jaws oriented at 90 degrees to the handle. In theory it is used to turn nuts and bolts, in practice it rounds over nuts and bolts. A monkey wrench is similar to a pipe wrench at first glance- but has parallel jaws with small (if any serrations).

How much is a 24 inch rigid pipe wrench?

RIDGID 31030 Model 24 Heavy-Duty Straight Pipe Wrench, 24-inch Plumbing WrenchList Price: $74.70 You Save: $12.04 (16%)

What is a spud wrench?

A spud wrench is a wrench with an adjustable or standard box wrench on one end and a tapered spike on the other. The spike can be used to line up bolt holes when installing pipe fittings, doing automotive work or—in the case of iron workers—for lining up bolt holes in girders and beams.

ncG1vNJzZmiemaOxorrYmqWsr5Wne6S7zGifqK9dmbxuxc6uZKadkajCs7GMmmSpoaCaeri%2BxKeaoQ%3D%3D